Risultati da 1 a 2 di 2

Discussione: ASUS ROG Rampage IV Extreme - Overclock

  1. #1
    L'avatar di Carlo
    Title
    Nerd
    Data Registrazione
    Oct 2006
    Età
    34
    Messaggi
    6,717

    Predefinito ASUS ROG Rampage IV Extreme - Overclock

    ASUS ROG Rampage IV Extreme
    Overclocking da record del mondo

    Republic of Gamers (Repubblica dei Giocatori) rappresenta il meglio del meglio. Offriamo il meglio dell´ ingegneria hardware, rapidissime prestazioni nonchè le idee più innovative, per dare il benvenuto ai migliori giocatori!


    Qui la compassione è solo per i deboli e vantarsi dei propri diritti significa tutto.Crediamo nelle affermazioni propositive e primeggiamo nelle competizioni. Se vi ritrovate in questa descrizione, unitevi a questo club esclusivo e fate sentire la vostra presenza in " Republic of Gamers"


  2. #2
    L'avatar di Carlo
    Title
    Nerd
    Data Registrazione
    Oct 2006
    Età
    34
    Messaggi
    6,717

    Predefinito

    TIPS Overclock by Shamino
    Download latest 0076b
    [Solo gli utenti registrati possono vedere questo collegamento. ]

    Fixes Cold boot problem during High CPU OCs

    Download Latest OCpak:
    [Solo gli utenti registrati possono vedere questo collegamento. ]

    Ignore the ROG Connect version inside and use this version:
    [Solo gli utenti registrati possono vedere questo collegamento. ]

    Latest OC Key Firmware:

    [Solo gli utenti registrati possono vedere questo collegamento. ]

    Flashing OC Key Firmware
    Connect ROG white USB cable from PC to OCKey USB port
    Make sure OC Key Cable is connected from MB to OC Key (MB needs to be at least in Standby Mode)
    Run F/W Update

    Download latest Indepth guide:
    [Solo gli utenti registrati possono vedere questo collegamento. ]

    Extreme Overclocking Steps
    1. Find out your best temperature for your RAM/IMC speeds/config.
    2. Set your OC settings and save and exit at that temperature. (Don’t worry about the Turbo Core Ratio since that only kicks in once you start loading the OS)
    3. After the bootup, go into the BIOS again.
    4. Set RC WARM boot fast under Memory Timings to Enabled so that you don’t retrain Memory at reboots.
    5. Set ClockGen Full Reset to Disabled if you plan to change BCLKs in OS and do not want a powerdown-powerup at reboots. (If you powerup with ClockGen Full Reset Disabled you may have problems booting so either do an OC recovery or clearcmos and load profile with it enabled)
    6. Start pulling temperatures down and when ready, just save and exit.

    Here is my actual bench procedure
    Load extreme oc profile low current
    Set core ratio to 42x
    Set bclk to 131 or more (etc etc depends on max cpu frequency can start lower cpu ratio)
    Set dram freq to 2444 or more (depends on ur imc/dram)
    Under dram timings set load tight psc profile if using psc
    Set vcore to 1.65v
    Set vtt to 1.35v
    Set vsa to 1.35v
    Set both dram voltage to 1.85v
    Set cpu pll to 2.10v
    Wait till around -30+C and save exit
    Go back to bios to set RC WARM boot fast & ClockGen Full Reset to Disabled & save exit
    Enter os around -40+c

    Notes:
    Stalling at DEBUG Port 79 – Happens when CPU is stretched with DRAM and BCLK. Can use Slow Mode to pass this part

    Keep seeing Please Enter BIOS to recover settings and BIOS doesn’t save settings. Clear CMOS and enter BIOS, load defaults and save and exit once.

    When you face message ‘System Unstable. Your CPU Ratio may be down at 12x due to unsuitable conditions’ – Choosing the right ClockGEN Filter setting or Turbo Mode functionality or CPU Running temperature will fix this. Note that when this message pops up, pressing reset or power button yields no response.

    When you keep pressing reset or crashes during booting and Voltiminder’s LEDs light up and don’t extinguish and DEBUG port stops at ‘70’, turn off AC and back on to power on normally.

    DEBUG port stops at ‘40’. Press power off for 4 seconds and then back on again.

    When benching cold, it is easier to pass the MRC Memory Training when at high Memory Frequencies at a warmer temperature than when you are benching.

    The IMCs on CPUs may vary greatly on Memory Frequency, if you see the Memory Training at initial boot go ‘b1’ directly into a ‘00’, that means the CPU’s IMC is not capable of the target frequency.
    If it goes after b1 into a 00 or a b3 or b4 that means the cpu’s imc is not capable of the frequency and no matter what rams or board wont matter. If its timings etc then u should at least see a b7 and after that some crash debug ports like 01 32 shutdown etc So it will be like:
    00 after b1 – totally incapable
    B3 / b4 – imc maxin out trim down a few mhz and it will pass

    So assuming everything is fine then increasing freq 1mhz 1mhz your cpu imc will go pass to b3/b4 and then 00
    This isn’t like Sandy Bridge whereby you can test clock walls at air-cooling, you need cold.

    Set the appropriate DRAM CLK Period to maximize Superpi Times

    You will need high VDIMM for Elpida Hypers to scale

    Set Rampage Tweak to Mode 1 for DRAM Compatility or to Mode 2 for DRAM OC

    start testing high bclk by setting 155 bclk and Set ClkGen Filter to disabled when pushign bclk to 150+

Discussioni Simili

  1. Bergamo [BG] Cerco ASUS RAMPAGE III Extreme
    Di SchedaVideo nel forum Acquisto
    Risposte: 0
    Ultimo Messaggio: 18-10-2014, 19:46
  2. Asus Rampage Extreme 2
    Di Katzuya nel forum Schede Madri & Ram
    Risposte: 6
    Ultimo Messaggio: 13-04-2009, 03:06
  3. Asus Rampage Extreme 2
    Di Katzuya nel forum Presentazioni
    Risposte: 0
    Ultimo Messaggio: 11-04-2009, 11:46
  4. Scheda Madre Asus rampage II extreme
    Di rubber nel forum Schede Madri & Ram
    Risposte: 14
    Ultimo Messaggio: 03-02-2009, 15:15
  5. Foto della Asus Rampage Extreme X48
    Di nVegeth nel forum Schede Madri & Ram
    Risposte: 28
    Ultimo Messaggio: 01-08-2008, 00:16

Tag per Questa Discussione

Permessi di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •